蒂森MC2-B故障代碼詳解V1.8

故障代碼,故障子碼,故障名稱,故障原因,故障等級,,備注2

0xAFFD,2701,未檢測到上平層開關,電梯上行時，下平層開關OFF期間上平層開關未發生變化。,1級,,

0xAFFD,2801,未檢測到下平層開關,電梯上行時，下平層開關OFF期間上平層開關未發生變化。,1級,,

0xAFFF,5801,碼板學習錯誤Codeboardlearningerror,"1、上下平層編碼學習不一致

2、端站碼板錯誤

1.Theupperandlowerlevelcodinglearningisinconsistent;

2.Terminalfloorcodeboarderror",1級,,

0xAFE6,5802,檢測到相同碼板Samecodeboarddetected,檢測到兩塊相同碼板Samecodeboarddetected,1級,,

0xAFE1,5803,"碼板缺口或凸出>255mm

Pergridunit>255mm","碼板缺口或凸出>255mm

Pergridunit>255mm",,,

0xAFE2,5804,"碼板缺口或凸出<7mm

Pergridunit<7mm","碼板缺口或凸出<7mm

Pergridunit<7mm",,,

0xAFFD,6801,兩個平層開關都未檢測到,電梯上行時，1級下減速開關從on到off，兩個平層開關都未變化,1級,,

0xAFFE,6802,平層開關反接,上，下平層開關狀態從ON，ON到OFF，ON，出現這種情況認為平層開關反接,1級,,

0xAFE3,6803,平層插板太長,"1.F123=0,(平層插板長度+平層開關間距)/2大于900mm

2.F123=1,碼板長度>750

1.F123=0,(Lengthofplate+distanceoftheswitch)/2>900mm

2.F123=1,Lengthofplate>750",1級,,

0xAFE4,6804,平層插板太短,"1.F123=0,(平層插板長度+平層開關間距)/2小于100mm.

2.F123=1,碼板長度<650

1.F123=0,(Lengthofplate+distanceoftheswitch)/2<100mm

2.F123=1,Lengthofplate<650",1級,,

0xAFE3,6805,平層區太長,"1.F123=0,(平層插板長度-平層開關間距)/2大于100mm.

2.F123=1,平層區>80

1.F123=0,(Lengthofplate-distanceoftheswitch)/2>100mm

2.F123=1,distanceofLevelingzone>80",1級,碼板時，更容易觸發5801，還來不急觸發這2個,

0xAFE4,6806,平層區太短,"1.F123=0,(平層插板長度-平層開關間距)/2小于10mm

2.F123=1,平層區<48

1.F123=0,(Lengthofplate-distanceoftheswitch)/2<10mm

2.F123=1,distanceofLevelingzone<50",1級,,

,6807,平層開關之間距離不符合要求（按照星瑪程序做）,"平層開關間距離大于380mm或小于30mm

根據4m/s，每2ms檢測一次平層開關，就是8mm，就是說兩平層開關之間最少間距16mm可以分辨出來，加點余量30mm",1級,,

,6808,平層插板的長度不符合要求（按照星瑪程序做）,平層插板的長度大于400mm或小于50mm,1級,,

,6809,平層插板和平層開關距離之差偏小（按照星瑪程序做），將68故障分為兩個68016802,平層插板和平層開關距離小于20mm,1級,,

0xAFE3,6807,門區插板太長DoorZoneplateisextremelylong,"F123!=0,插板長度>900

F123!=0,Lengthofplate>900",1級,基本不會出現，優先觸發軟限位,增加F123

0xAFE4,6808,門區插板太短DoorZoneplateisextremelyShort,"F123!=0,插板長度<100

F123!=0,Lengthofplate<100",1級,,增加F123

0xAFEB,6809,開關間距太長distanceoftheswitchisextremelylong,"F123=1,開關間距>48

F123=1,distanceoftheswitch>48",1級,,增加F123

0xAFEB,6810,開關間距太短distanceoftheswitchisextremelyShort,"F123=1,開關間距<24

F123=1,distanceoftheswitch<24",1級,,增加F123

0xAFE5,6901,自學習樓層與設置樓層不符,通過自學習學得的樓層與參數設置的樓層不一致,1級,,

0xAFEF,6902,樓層高度太長,樓層高度大于8m,1級,,

,10,樓層高度太短,樓層高度小于0.5m,1級,,

0xAFEF,6903,樓層高度太短Minimumstoreyheightisextremelyshort,"樓層高度小于（插板長度+50）

Minimumstoreyheight<(Lengthofplat+50)",1級,碼板時，無法支持這么短樓層，此時碼板都讀不對,

0xFF02,1101,1級下減速開關丟失,1級下減速開關以上的減速開關動作時，未學習到1級下減速開關,1級,,

0xFF02,1102,1級下減速開關距端站距離太短,"當減速開關級數大于1級，1級下減速開關動作位置低于底層樓層高度位置的3/5

否則，1級下減速開關動作位置低于最短減速距離",1級,,

0xFF03,,1級下減速開關安裝位置過高（不要此故障，當自學習樓層大于等于2時，沒學習到1級下減速開關）,減速開關安裝位置大于底層高度,1級,,

0xFF02,1109,"不在底層，1級下減速開關與門區開關同時動作Notatthebottomfloor,thelowerdecelerationswitchanddoorzoneswitchareinactionatthesametime","F123!=0不在底層，門區開關動作時，下減速開關有效

F123!=0下減速開關從OFF到ON時，門區開關也有效

Notatthebottomfloor,thelowerdecelerationswitchiseffectivewhendoorzoneswitchisoperated",1級,,F123

0xFF01,1001,1級上減速開關丟失,未學習到1級上減速開關,1級,,

0xFF01,1002,1級上減速開關距端站距離太短,"當減速開關級數大于1級，1級下減速開關動作位置高于頂層樓層高度位置的3/5

否則，1級上減速開關動作位置高于最短減速距離",1級,,

0xFF03,,1級上減速開關動作多次（不要此故障，當自學習樓層大于等于2時，不學習1級下減速開關）,自學習過程中1級上減速開關動作多次,1級,,

0xFF01,1009,"不在頂層，1級上減速開關與門區插板同時動作Notatthetopfloor,upperdecelerationswitchanddoorzoneswitchareinactionatthesametime","F123!=0不在頂層，門區開關動作時，上減速開關有效

F123!=0上減速開關從OFF到ON時，門區開關也有效

Notatthetopfloor,theupperdecelerationswitchiseffectivewhendoorzoneswitchisoperated",1級,,F123

0xFF04,1301,2級下減速開關丟失,2級下減速開關以上的減速開關動作時，未學習到2級下減速開關,1級,,

0xFF04,1302,2級下減速開關距端站距離太短,"S=3級下減速開關動作點的下一個樓層位置-底層位置

當減速開關級數大于2級，2級下減速開關動作位置低于S的3/5

否則，2級下減速開關動作位置低于最短減速距離",1級,,

0xFF03,,2級下減速開關動作多次,自學習過程中2級下減速開關動作多次,1級,,

0xFF03,1201,2級上減速開關丟失,2級上減速開關以上的減速開關動作時，未學習到2級上減速開關,1級,,

0xFF03,1202,2級上減速開關距端站距離太短,"S=底層位置-3級上減速開關動作點的上一個樓層位置

當減速開關級數大于2級，2級上減速開關動作位置高于S的3/5

否則，2級下減速開關動作位置高于最短減速距離",1級,,

0xFF03,,2級上減速開關動作多次,自學習過程中2級上減速開關動作多次,1級,,

0xFF06,1501,3級下減速開關丟失,3級下減速開關以上的減速開關動作時，未學習到3級下減速開關,1級,,

0xFF06,1502,3級下減速開關距端站距離太短,"S=4級下減速開關動作點的下一個樓層位置-底層位置

當減速開關級數大于3級，3級下減速開關動作位置低于S的3/5

否則，3級下減速開關動作位置低于最短減速距離",1級,,

0xFF03,,3級下減速開關動作多次,自學習過程中3級下減速開關動作多次,1級,,

0xFF05,1401,3級上減速開關丟失,3級上減速開關以上的減速開關動作時，未學習到3級上減速開關,1級,,

0xFF05,1402,3級上減速開關距端站距離太短,"S=底層位置-4級上減速開關動作點的上一個樓層位置

當減速開關級數大于3級，3級上減速開關動作位置高于S的3/5

否則，3級下減速開關動作位置高于最短減速距離",1級,,

0xFF03,,3級上減速開關動作多次,自學習過程中3級上減速開關動作多次,1級,,

0xFF08,1701,4級下減速開關丟失,4級下減速開關以上的減速開關動作時，未學習到4級下減速開關,1級,,

0xFF08,1702,4級下減速開關距端站距離太短,4級下減速開關動作位置低于最短減速距離,1級,,

0xFF03,,4級下減速開關動作多次,自學習過程中4級下減速開關動作多次,1級,,