T/GDMIA 013-2024滾壓滾珠絲杠副檢驗驗收

ICS25.040.20

CCSJ51

團體標準

T/GDMIA013—2024

滾壓滾珠絲杠副檢驗驗收

Inspectionandacceptanceofrolledballscrewassembly

2024?06?20發布2024?07?20實施

廣東省機械行業協會發布

中國標準出版社出版

T/GDMIA013—2024

目次

前言··························································································································Ⅲ

1范圍····················································································································…1

2規范性引用文件·····································································································…1

3術語和定義···········································································································…1

4滾壓滾珠絲杠副分類·······························································································…2

4.1內循環··············································································································2

4.2外循環··············································································································2

4.3端面循環···········································································································2

5檢驗條件··············································································································…3

5.1分級標準···········································································································3

5.2顏色方案···········································································································3

5.3幾何精度驗收標準·······························································································3

6驗收檢驗··············································································································…3

6.1概述·················································································································3

6.2定位級行程偏差和變動量······················································································5

6.3傳動級行程偏差和變動量······················································································6

6.4跳動和位置公差··································································································7

6.5柔順性·············································································································17

參考文獻····················································································································20

Ⅰ

T/GDMIA013—2024

前言

本文件按照GB/T1.1—2020《標準化工作導則第1部分：標準化文件的結構和起草規則》的規

定起草。

請注意本文件的某些內容可能涉及專利。本文件的發布機構不承擔識別專利的責任。

本文件由深圳市威遠精密技術有限公司提出。

本文件由廣東省機械行業協會標準化工作委員會歸口。

本文件起草單位：深圳市威遠精密技術有限公司、安徽省威遠精密工業科技有限公司、航天晨光股

份有限公司、滁州市華納傳動科技有限公司、力姆泰克（廊坊）傳動設備有限公司。

本文件主要起草人：李敬宇、李一前、陳潔、陳宣勻、胡毅、劉進江、鐘健、孟自明、賈丹峻。

Ⅲ

T/GDMIA013—2024

滾壓滾珠絲杠副檢驗驗收

1范圍

本文件規定了滾壓滾珠絲杠副檢驗驗收的項目及允差值，描述了滾壓滾珠絲杠副的檢驗方法。

本文件適用于機械制造行業用的滾壓滾珠絲杠副產品，其他相關行業亦可參照使用。

2規范性引用文件

下列文件中的內容通過文中的規范性引用而構成本文件必不可少的條款。其中,注日期的引用文

件,僅該日期對應的版本適用于本文件；不注日期的引用文件，其最新版本(包括所有的修改單)適用于

本文件。

GB/T17587.1—2017滾珠絲杠副第1部分：術語和符號

GB/T17587.3—2017滾珠絲杠副第3部分：驗收條件和驗收檢驗

ISO3408?3：2006Ballscrews—Part3：Acceptanceconditionsandacceptancetests

DIN69051?1Werkzeugmaschinenkugelgewindetriebebegriffe，bezeichnungssystem

T/GDMIA003—2019滾壓滾珠絲杠

3術語和定義

GB/T17587.1—2017界定的以及下列術語和定義適用于本文件。

3.1

柔順性compliance

滾壓滾珠絲杠副摩擦特性的直觀體現。其狀態表現為滾壓滾珠絲杠副低速及高速旋轉時，滾珠循

環滾動所體現的工藝性、靈活性、準確性、穩定性等。

3.2

桃形溝gothicprofile

滾珠絲杠及其滾珠螺母的螺紋法向截面圖形呈現兩個對稱但不同圓心的圓弧形狀。其雙圓弧形

狀特征與植物桃的外形相似。

3.3

DN值DNvalue

mmr/min

滾珠絲杠副公稱直徑